Women's R-3 One Piece Suit

$1,547.00
SKU
510

The R-3 (Roadcrafter 3) is the third-generation one piece Aerostich suit. It is 100% waterproof and unlined for maximum airflow, yet slips quickly and easily over your street clothes. Its full-length waterproof zipper entry system is fast, and it doesn’t flutter or flap in the wind. Without a lining it wears cooler, and with seam-sealed rainproof zippers you’ll also stay completely dry, even during the wettest conditions.

Each R-3 takes more than an hour longer to manufacture than previous Roadcrafters, but it’s worth it. You’ll enjoy higher levels of performance, comfort, and protection on every ride. And like its predecessor Roadcrafters, the R-3 is constructed of Aerostich’s exclusive American-made mil-spec 500d Cordura® TLTex® fabric. It’s a strong, long-lasting and highly abrasion-resistant material ideal for this use.

For increased protection there’s a double layer of this fabric across the seat, and added 1000d abrasion-resistant layers covering the vital elbow/shoulder/knee areas. Beneath each of these is a superior energy absorbing system utilizing removable, oversized TF impact armor. Each armor attachment point is adjustable to allow fit to be fine-tuned for comfort and ensure it stays in place for best protection. Separately available hip, spine and chest armor options further increase the R-3’s capabilities.

With its oversize two-slider underarm vents, a two-slider back vent and magnetic clasps to hold open the fold-down dual-height collar, you ride cool and protected at the same time. As temps drop and when precipitation comes you’ll remain cozy and dry, too, because the adjustable Ultrasuede collar fits comfortably around your neck, even with varying base-layers.

Additional features include flap covered hip-side water resistant zippers for fast access to your street pants, a hidden pass-thru port for an electric liner power cord, nine strategically placed everyday-useful pockets, a mini-carabiner helmet holder at the upper chest pocket, a highly water-resistant inner wallet/phone/iPod pocket, fit-adjustable ankle and wrist tabs, articulated knees, fit-adjustable waist tabs and an integrated stretch panel across the lower back. There’s also oversize 3M Scotchlite® reflective areas across the back, chest and ankles to enhance conspicuity in low light conditions.

Over 30 standard color combinations give each R-3 a personalized style, and add-on options include Integrated Boot Raincovers, electrically heated and non-heated Chest Insulation and Impact Pads, an Emergency Medical Info Pocket, and detachable arm and thigh Map and Accessory Pockets.

Three standard body colors: black, grey, or hi-viz lime yellow. Six standard abrasion area colors: black, grey, hi-viz lime yellow, cobalt blue, red, or pink. Machine washable. Women’s sizes 2-20 short, regular or long. Choose TF3 or TF6 armor. Made in America Made in America and Imported.

Additional Information/Resources:

Getting the Perfect Fit

Getting the Perfect Fit

  • All Roadcrafters are available in more than sixty in-stock sizes, with a wide range optional fitting-alterations if needed. Men’s models are stocked by suit (chest) size in ‘short’, ‘regular’ and ‘tall’ versions. Women’s models are stocked by dress size in short, regular and tall versions, too. Inventoried stock sizes are shipped within 24 hours.
  • Roadcrafters are intended to fit nicely over a layer of street clothing, so if you wear a size 40R men's blazer or sport coat…or a size 8L women’s dress…select the same size Aerostich jacket or suit. If you’re unsure of your size, see the sizing chart guidelines, or contact us (218 722 1927, [email protected]) and we’ll help you get the right fit. We will ask for information about your height, weight, chest/suit or dress size, and your jeans or pants ‘waist x inseam’ size.
  • Find detailed information about ordering optional alterations, non-stock colors and specialized features here. Fully custom made-to-measure garments are not available. Standard suit colors are mix & match Black, Grey and Hi-Viz Lime Yellow body areas with your choice of Black, Grey, Silver, Hi-Viz abrasion areas. Request free color swatches here.

Hassle Free Sizing Exchange

If you happen to need a different size, just return the suit and we'll ship out a replacement free of charge (domestic ground shipments only).

Roadcrafter Classic vs. R-3

What is the Difference Between a Roadcrafter Classic and an R3?

The RC Classic is the original Aerostich suit and it has been continually manufactured, updated and refined for over thirty-five years now. It is a fully lined garment and was created to be an armored coverall intended primarily for commuting applications. It is constructed the same way a leather rider’s suit is, but in textiles so it is lighter and cooler to wear. For this reason (the way it is designed to be put together) it isn’t perfectly waterproof. But still it has always worked better than conventional leather gear in most hot and wet situations. Roadcrafter Classic suits have been worn world-wide and they continue to satisfy thousands of riders which is why it remains available. It is comfortable and functional. Some of our customers are now on their third or fourth one.

The R-3 is the third generation Aerostich one-piece coverall. It’s unlined like a lot of today’s most technical and lightweight waterproof outdoor gear, and it does pass the rigorous certification for rainwear. We sometimes think of it as an armored and highly abrasion-resistant rain suit. Its impact armor is attached to the inside with adhesively bonded hook-and-loop. This suit wears slightly cooler in really hot conditions absent a separate inner lining. There are numerous other small refinements the RC Classic does not have.

In summary, the RC Classic has become an actual classic just as ‘Levi’s 501’ denim jeans and many other long-popular products. Many riders like it exactly the way it is. The R-3 waterproof one-piece suit is what we make today for the same intended applications but incorporating the technology and experience we now have.

We're Not Sure How to Make These Suits Look Cool

We Are Not Sure How To Make These Suits Look Cool

“We understand that looking cool is a huge factor in our contentment. You can’t imagine how strongly I wish we knew how to make these suits look cool. They were created to be more equipment than fashion, so they look the way they do because of how we want them to function.

“There are many cultural constructs surrounding riding motorcycles, especially in wealthy and advanced parts of the world, and these suits don’t quite fit into most of them. The core idea is simply to be able to ride more, to more kinds of destinations, wearing more kinds of ‘street’ clothing beneath, in more kinds of ambient weathers. I can tell you from hard experience that wearing an R-3 into a grocery store (or in any other business or public situation) can involve social awkward-ness. After awhile some riders begin to find this experience amusing. Aerostich suit wearers share stories about their encounters with ‘a confederacy of dunces’ when wearing one of these suits.

“That phrase is a fairly well-known Jonathan Swift quote that reads in full: ‘When a true genius appears in the world, you may know him by this sign, that the dunces are all in a confederacy against him.’ It’s from Thoughts on Various Subjects, Moral and Diverting.

“Our one-piece riding suits came mostly from a strong desire to be able to ride more. Back in 1980 I was a 28 year old casual recreational motorcyclist, mostly riding trails and a few weekend AMA enduros. I was also coming to the conclusion that I would not be ‘outgrowing’ motorcycling as I had sort of expected would happen. No others in my family were riders.

“Three years later we began working on creating these suits simply to be able to ride to work wearing street clothing with some functional level of protection (weather, impact, abrasion…) in as easy-to-use form as possible. And hoping there were enough others who wanted something like this to be able to make a small business out of it.

“If you have the interest and don’t mind the geeky (and mildly subversive?) aspects of wearing a highly technical coverall, give one a try. You’ll end up riding more.”

Mr. Subjective
How to Get a Functional, Comfortable One-Piece Suit Fit

How to Get a Functional, Comfortable One-Piece Suit Fit:

Start with your height and body length…For a person’s given overall height, some will have longer-bodies-with-shorter-legs, and others have shorter-bodies-with-longer-legs. After a suit is sewn and completed there is no simple or cost-effective way to then make the garment’s torso length (the distance from crotch to collar) shorter or longer. A few specialized alterations can help slightly (see 'ellipse' below), but they are imperfect Band-Aids.

Garage mechanics and others who wear coveralls for a living know a lowish crotch and baggy seat means they’ll be able to raise their arms upward fully and comfortably. When one does this arm-raising to horizontal, the entire torso section of a one-piece suit slides upwards about 1.5". The suit’s bulky shoulder impact armor move it that way. And when you lower your arms, the suit body area should slide back downward smoothly.

Aerostich gear is graded by chest size (38, 40, 42, 44, etc) and each is available in short (S), regular (R) and long (L) versions. If you are borderline height-wise, part-way between an ‘S’ and an ‘R’, go with the longer body length of the ‘R’. And if you are somewhere between an ‘R’ and an ‘L’, go with the longer body of the ‘L’. The extra body length in each size is about 1.3" greater. And if you ride a sport bike, or are an especially active rider and want maximum freedom-of-movement, a slightly longer body sometimes works and feels a bit better.

Leg and sleeve lengths should be adjusted as needed after your body/torso length has been determined. For a comfortable and correct fit with your raised arms out to your side horizontally (both at the same time), you should still have very slight room at the crotch.

The suit’s body, sleeve and leg diameters are exactly the same for each ‘S’, ‘R’ and ‘L’ version of a particular size. For example, the dimensions around your body of the 38S, 38L and 38R are identical. The circumferences are exactly the same.

A riding suit’s leg lengths are correct if, when standing normally, the hem breaks (wrinkles) slightly against the front of your riding boot just above the foot’s arch, and the top edge of the TF knee impact armor cup is positioned near the center of your kneecap. Then, as you sit on your bike, the hem will rise about 1.5” and the knee armor cup will slide upward and center itself over your bent knee.

A riding suit’s sleeves are the correct length if, when standing normally with your arms hanging loosely by your sides, they end about mid-way between your knuckles and your wrist, measured at the center back of your hand. The center of the TF impact armor elbow cup should also be centered on, or very slightly below, your elbow.

Specialized Motorcycle Configuration Considerations:

For comfort with low handle bars and higher positioned rear-set footrests, all one-piece riding suits will fit better with the ‘Extra Forward Rotated Sleeve’ alterations, and may also benefit from an ‘ellipse’ added to the center of the back. In addition, an ‘expanded knee’ alteration is available which provides slightly more space for knee armor when knees are bent more sharply.

For active off-road riding requiring maximum freedom-of-movement and upper-arm ease, underarm ‘V’ gussets may be added to increase upper sleeve diameter and provide extra room across upper chest and shoulder areas.

Suit Tips and Helpful Hints

Learning Your New Roadcrafter Classic or R 3 Suit: Tips and Helpful Hints.

Yes, there is a break in period…Your new suit may feel stiff compared to more familiar types of clothing. You’ll experience improvements in comfort, fit and function the more you ride, from first few miles and onward (nearly indefinitely). All Roadcrafter and R-3 suits continue to improve with added wear and miles.

The best way to put on an R-3 or Roadcrafter Classic suit is to hold it in front of you by it’s ‘chest’,one hand on each side of the fully separated main zipper. Then, lower the garment slightly while moving it slightly to the right and raise your right leg and put it into the right leg of the suit. Next, pull the entire garment upward, release your right hand from the front of the suit and put it into the right sleeve, exactly as you would pull on a jacket. Lastly, your left arm goes into the left sleeve (just where you’d expect) and you are ready to start zipping up (…down, actually).

This does take a bit of practice, but it quickly becomes natural, fast and easy. It’s the best way to get into a one-piece coverall with the least amount of bending and contorting, and the garment also spends the least amount of time dragging on the ground. That’s why it’s two main entry zippers are on the 'inside', instead of the outside (as on work coveralls, where the zippers are on the outside of the legs and the front zipper only goes to the crotch). This extra ease is important because your suit's intended purpose is as an ‘all-in-one’ protection and comfort solution for daily commuting and short-hop A-to-B riding. For when you want better protection than your street clothing provides with less rigmarole than changing into conventional gear.

To more quickly learn the suit’s unusual main zipper, which starts nearly under one's chin,practice in front of a mirror a few times to memorize how to hold and engage the two main zipper sliders. These slider ‘handles’ are captured close together between the knuckles of the first three fingers of your right hand. Your opposite (left) hand then slides the other side of the zipper’s end into both sliders. After being fully inserted, release the two slider handles from between your knuckles and grasp only the lower slider’s handle. Then zip it downward to about your knee. At that point either lift and bend your left leg slightly and complete the zip, or bend over slightly and zip to the bottom. Most suit wearers seldom (or never) use the snap at the bottom of the zipper.

The removable collar hold-open magnets make it easier to ventilate the suit in hot conditions and are especially useful if you ride a motorcycle with a fairing or windshield, but they do have limitations. If your local climate isn't always warm, remove and put the magnets on the side of your tool box or refrigerator. Otherwise you might sometimes end up fighting with them as they try to keep the collar open when you wish to keep it closed.

Your new Aerostich suit will wear perfectly when the weather is nice, and will feel even better when the weather is lousy. You may discover that riding places in bad weather, when nobody else is out riding, is fun. It can be a little extra-satisfying to be on two wheels when everyone else on the road has no idea why you are out there in the first place…much less that you are reasonably comfortable. And if you’ve ever thought some non-riders might have considered you slightly ‘off’ because you enjoyed riding in the first place, wait until you walk into a workplace or grocery store wearing your dripping Aerostich suit after riding there thru a severe rainstorm. No amount of nice friendly smiling on your part will be enough. So enjoy the ride.

Download these Hints

Heated Gear Power Cord Port

Details Make a Difference: Heated Gear Power Cord Port

Photo: Heated Gear Power Cord Port

Photo courtesy of John Blowitz

(Click to enlarge)

This hidden cord port is part of all one piece Roadcrafter Classics and R-3s. It's a pass-thru for a short wire that connects any electrically heated clothing to the outside of the garment. The other side of this pass-thru is inside the slash pocket located behind the lower flapped pocket on the left side.

How it works is you position either a coily power cord (#172) or jumper cord (#162) so the end of the cord that connects to the electric garment is dangling out of this port on the inside of the suit. The other end is 'stored' in the slash pocket that forms behind the lower left flapped pocket on the outside of the suit.

When you are ready to ride somewhere with an electric garment beneath the suit, you first put on the electric garment. Then you put on the suit. Then you connect the power cord or jumper cord to the electric garment. Then you zip the suit closed around you. Then you get on the motorcycle (or stand close to it) and remove the other end of the cord from the slash pocket located behind the flapped pocket and plug it into the power on the motorcycle. Then you ride away warm and comfortable.

Shoulder Mount for GoPro Cameras

Shoulder Mount for GoPro Cameras

Shoulder Mount for GoPro Cameras

Camera Pocket Loop

By far the best POV (point of view) location, for the best film result, because it shows the rider’s hands, handlebar and motorcycle’s instruments at the bottom of the frame. There’s no comparison to other mount locations. Far nicer video results than are possible with a helmet cam, bar cam or tank cam mount. See the images and short video (link below). You won’t be disappointed.

PS - We’ve been offering this mount for ten years in our ‘optional and alterations’ product menu. Few noticed it. Then, in the fall of 2021 the ’shoulder mount' was introduced as an exciting and better way to get on-bike video by professional MotoGP video creators. It’s not new. It’s been available here for a long time. #344 $35.00

Write Your Own Review
Please Sign in or create an account to leave a review.

Choosing Elbow/Shoulder/Knee Armor:

  • Standard TF3 provides an optimal comfort/protection balance across average ambient temperatures (60ºf - 75ºf / 15ºc - 24ºc).
  • Stiffer Competition TF6 provides a slightly improved comfort/protection balance in higher ambient temperatures (70ºf - 95ºf / 21ºc - 35ºc).

Available only in complete sets according to suit purchased (shoulders and elbows for jackets; knees only for pants; and shoulders, elbows, and knees for one piece suits).

Women's Sizing Chart

Size Bust Waist Hip Height Weight (lbs) Back Sleeve Length Inseam Back Waist Length Girth*
2 Short 34" (86cm) 29 1/2" (75cm) 37" (94cm) 5'0"-5'2" (152-157cm) 85-100 (38-45kg) 27 1/8" (69cm) 28 1/8" (71cm) 13 1/8" (33cm) 55" (140cm)
2 Regular 5'2"-5'4" (157-163cm) 90-105 (41-48kg) 29" (74cm) 30" (76cm) 14 1/4" (36cm) 58" (147cm)
2 Long 5'4"-5'6" (163-168cm) 95-110 (43-50kg) 30 1/8" (77cm) 31 1/8" (79cm) 15 3/8" (39cm) 61" (155cm)
4 Short 36" (91cm) 30 1/2" (77cm) 38" (96cm) 5'1"-5'3" (155-160cm) 95-110 (43-50kg) 27 5/8" (70cm) 28 3/8" (72cm) 13 4/9" (34cm) 56 3/8" (143
4 Regular 5'3"-5'5" (160-165 cm) 100-115 (45-52kg) 29 1/2" (75cm) 30 1/4" (77cm) 14 5/9" (37cm) 59 3/8" (151cm)
4 Long 5'5"-5'7" (165-170cm) 105-120 (48-54kg) 30 5/8" (78cm) 31 3/8" (80cm) 15 2/3" (40cm) 62 3/8" (158 cm)
6 Short 37" (94cm) 31 1/2" (80cm) 39" (99cm) 5'2"-5'4" (157-163cm) 105-120 (48-54kg) 28 1/8" (71cm) 28 5/8" (73cm) 13 3/4" (35cm) 57 3/4" (147cm)
6 Regular 5'4"-5'6" (163-168cm) 110-125 (50-57kg) 30" (76cm) 30 1/2" (77cm) 14 7/8" (38cm) 60 3/4" (154cm)
6 Long 5'6"-5'8" (168-173cm) 115-130 (52-59kg) 31 1/8" (79cm) 31 5/8" (80cm) 16" (41cm) 63 3/4" (162cm)
8 Short 38" (96cm) 32 1/2" (83cm) 40" (102cm) 5'3"-5'5" (160-165cm) 115-130 (52-59kg 28 5/8" (73cm) 28 7/8" (74cm 14" (36cm) 58 1/8" (148cm)
8 Regular 5'5"-5'7" (165-170cm) 120-135 (54-61kg) 30 1/2" (77cm) 30 3/4" (78cm) 15 1/5" (39cm) 61 1/8" (155cm)
8 Long 5'7-5'9" (170-175cm) 125-140 (57-63kg) 31 5/8" (80cm) 31 7/8" (81cm) 16 1/3" (41cm) 64 1/8" (163cm)
10 Short 39" (99cm) 33 1/2" (85cm) 41" (104cm) 5'4"-5'6" (162-168cm) 125-145 (57-66kg) 29 1/8" (74cm) 29 1/8" (74cm) 14 3/8" (37cm) 60 1/2" (154cm)
10 Regular 5'6"-5'8" (168-173cm) 130-150 (59-68kg) 31" (79cm) 31" (79cm) 15 1/2" (39cm) 63 1/2" (161cm)
10 Long 5'8"-5'10" (173-178cm) 135-155 (61-70kg) 32 1/8" (82cm) 32 1/8" (82cm) 16 5/8" (42cm) 66 1/2" (169cm)
12 Short 40 1/2" (103cm) 35" (89cm) 42 1/2" (108cm) 5'5"-5'7" (165-170cm) 135-155 (61-79kg) 29 5/8" (75cm) 29 3/8" (75cm) 14 2/3" (37cm) 61 7/8" (157cm)
12 Regular 5'7-5'9" (170-175cm) 140-160 (63-72kg) 31 1/2" (80cm) 31 1/4" (79cm) 15 4/5" (40cm) 64 7/8" (165cm)
12 Long 5'9"-5'11" (175-180cm) 145-165 (66-75kg) 32 5/8" (83cm) 32 3/8" (82cm) 17" (43cm) 67 7/8"(172cm)
14 Short 42" (107cm) 36 1/2" (93cm) 44" (112cm) 5'6"-5'8" (168-173cm) 145-165 (66-75kg) 30 1/8" (77cm) 29 5/8" (75cm) 15" (38cm) 63 1/4" (161cm)
14 Regular 5'8"-5'10" (173-178cm) 150-170 (68-77kg) 32" (81cm) 31 1/2" (80cm) 16 1/8" (41cm) 66 1/4" (168cm)
14 Long 5'10"-6'0" (178-183cm) 155-175 (70-79kg) 33 1/8" (84cm) 32 5/8" (85cm) 17 1/4" (44cm) 69 1/4" (176cm)
16 Short 43 1/2" (110cm) 38" (96cm) 45 1/2" (116cm) 5'7"-5'9" (170-175cm) 160-170 (72-77kg) 30 5/8" (78cm) 29 7/8" (76cm) 15 1/5" (39cm) 64 5/8" (164cm)
16 Regular 5'9"-5'11" (175-180cm) 165-185 (75-84kg) 32 1/2" (83cm) 31 3/4" (81cm) 16 4/9" (42cm) 67 5/8" (172cm)
16 Long 5'11"-6'1" (180-185cm) 170-190 (77-86kg) 33 5/8" (85cm) 32 7/8" (84cm) 17 5/9" (45cm) 70 5/8" (179cm)
18 Short 45 1/2" (116cm) 40" (102cm) 47 1/2" (121cm) 5'8"-5'10" (173-178cm) 170-190 (77-86kg) 31 1/8" (79cm) 30 1/8" (77cm) 15 5/8" (40cm) 66" (168cm)
18 Regular 5'10"-6'0" (178-183cm) 175-195 (79-88kg) 33" (84cm) 32" (81cm) 16 3/4" (43cm) 69" (175cm)
18 Long 6'0"-6'2" (183-188cm) 180-200 (82-91kg) 34 1/8" (87cm) 33 1/8" (84cm) 17 7/8" (45cm) 72" (183cm)
20 Short 47 1/2" (121cm) 42" (107cm) 49 1/2" (126cm) 5'9"-5'11" (175-180cm) 180-200 (82-91kg) 31 5/8" (80cm) 30 3/8" (77cm) 16" (40cm) 67 3/8" (171cm)
20 Regular 5'11"-6'1" (180-185cm) 185-205 (84-93cm) 33 5/8" (85cm) 32 1/4" (82cm) 17" (43cm) 70 3/8" (179cm)
20 Long 6'1"-6'3" (185-190cm) 190-210 (86-95kg) 34 5/8" (88cm) 33 3/8" (85cm) 18 1/5" (46cm) 73 3/8" (186cm)

*Girth = Measure from the midpoint on the shoulder towards the front, through the crotch and back around to meet the midpoint of the shoulder.

More Sizing Info:

Between Sizes:

Overall length* difference is 1 1⁄4".

  • Example - 42 (S, R or L) suit is 1 1⁄4" longer (taller) overall than a size 40 (S, R or L) suit.

Short to Regular:

Overall length* difference is 3".

  • Example - A 42S is 3" shorter than a 42R.
  • Leg length difference is +1" above & +1⁄2" below the knee. The remaining 1 1⁄2" is in the Torso.
  • Sleeve difference is 1 1⁄4", shoulder to wrist.

Regular to Tall:

Overall length* difference is 2".

  • Example - A 42L is 2" longer (taller) than a 42R.
  • Leg length difference is +1⁄2" above knee & +1⁄2" below the knee. The remaining 1" is in the Torso.
  • Sleeve difference is 1".

* Overall length = collar to ankle

We can adjust the sleeve lengths, elbow armor position, leg length, knee armor position, and many other variables, but we cannot change the body/torso length. For semi-custom fitted garments, we start with the body/torso size that is the closest and change the arms and legs as needed.

A great fit is critical to the long-term enjoyment and satisfaction of any garment. This is something we do better than anyone else with graded off the rack sizes. There are about 32 standard R-3 sizes vs. about 8 with typical S, M, L, XL grading. If the crotch in an R-3 is slightly binding, the garment will never have a chance to become your 'go to' riding gear, and I'd like it to have that chance.

One piece coveralls are the best gear for day-to-day short-hop utility riding because they work as a complete protection system all in one garment. But like mechanic's and trade-worker's coveralls, for comfort the crotch needs to be low enough to never bind.

Mr. Subjective, 6-14

Shipping Guide Map


International Orders

Currency conversion rates are close estimates only. All sales are processed in dollars (USD) and conversions are made by card-processing banks on the actual transaction date.

USA Only

ECO Saver delivery times are not guaranteed. Not available for orders over $100.

USA

SURFACE and AIR delivery options are guaranteed.

Orders Eco Saver Surface Priority/3day* 2 Day* 1 Day* International Air**
under $ 50 $6-$12 $12-$19.50 $21-$28.50 $30-$39 $45-$54 $31-$91
$ 51-$ 100 $10.50-$18 $16.50-$25.50 $25.50-$34.50 $36-$45 $54-$63 $38-$121
$ 101-$ 200 Not Available $21-$28.50 $31.50-$40.50 $42-$54 $63-$75 $46-$151
$ 201-$ 400 Not Available $24-$31.50 $37.50-$46.50 $54-$63 $75-$87 $61-$181
Over $ 400 Not Available $27-$34.50 $43.50-$54 $63-$90 $84-$117 $91-$226

Surface transport only to US addresses.

*Add $12 to 1 day or 2 day for Alaska, Hawaii, and Puerto Rico. (Extended area charge of $12 may apply to rural areas.)

**Call for international rates. Depending upon country, most charges will be between these rates. Duties and Taxes are not included in the shipping price. FedEx may charge brokerage fees for some countries. You will be responsible for these charges.

AFO/APO Addresses: Orders will be shipped Priority Mail.


All in-stock Aerostich products and RiderWearHouse Catalog items ordered before 2pm CST will be shipped within 2 business days. (If a specific size and color of Roadcrafter suit is not in inventory, we will notify you with an estimated delivery date. Production time varies.) All standard Aerostich items may be sent back for a refund, but the item(s) being returned must be in new condition.

Worldwide Orders

Buying direct from the United States is easy and convenient. Credit cards, fax machines, direct dial telephone service, and air shipping allow easy transactions between countries. For estimates on Duty & VAT costs, visit https://www.simplyduty.com/import-calculator/, a third party import duty calculator.

We do not charge or cover duties, taxes or brokerage fees. FedEx may charge brokerage fees for some countries. You will be responsible for these charges.

© 2022 Aero Design & Mfg. Co. All Rights Reserved.