Electrical Accessories

This BMW switch coil cord easily connects your vest or liner directly to the standard BMW accessory socket on your bike. (BMW Socket (#108) is available separately and requires additional wiring to connect to the motorcycle battery).

Additional Information/Resources:

Standard BMW power sockets. Requires additional wiring.

Standard BMW Plug. Requires additional wiring.

Standard hookup for Kanetsu Vests and Liners. Length 30".

Additional Information/Resources:

Connect two garments to a single power plug.

Additional Information/Resources:

Standard hookup for Kanetsu Vests and Liners. 10 A Fuse. Length 25".

Additional Information/Resources:

Standard hookup for Kanetsu Vests and Liners. Illuminated push button on/off switch. Stretches from 3'–6'.

Additional Information/Resources:

Connect to a standard power socket on your bike...or your car, snowmobile, etc.

Additional Information/Resources:

A connector wire with a standard power socket that fits a cigarette lighter/accessory plug.

Additional Information/Resources:

A coil cord for connecting the vest to the motorcycle. The ultimate in simplicity and reliability. Remains flexible in all temperatures. Stretches from 1.5'–5'.

For hard wiring your GPS, radio, or other accessories. No springs, so it’s not susceptible to vibrations. The 20A includes two fuses for Garmin GPS’s, and features a rubber dust cap. The 30A includes one fuse, and features a water resistant cap and about a foot of wire on each end.

Provides a flush mount DC coax jack panel with a spring loaded cover. The six inch coax plug cable allows direct connection to DC coax power output. This is the same coaxial connector used in all Aerostich QuiConnect electric garment power cords.

Quickly stow away excess cord for your earbuds, headphones, electrical wire, etc., with these handy wire organizers. Flexible, virtually indestructible, and useful. Set of 3; black, red, white. OK, that’s a wrap (sorry…). 75"×.9"×.25".

This rugged 12V panel mount cigarette lighter power outlet socket is fitted with a rubber dust cap to keep out moisture and road grime. Installs easily and securely into any 1.2" hole. 6" wire leads. 1.5"×2.5". 12V/15A.

Ziptie to any handlebar or frame tube for a dependable source of power with all electrical accessories that have a standard cigar lighter plug. Useful for radar detectors, cell phone chargers, etc. Weatherproof spring-loaded flip top cover keeps out moisture, grit and grime. 3"×2"×1.75", with two 12" wire leads.

Put power wherever you need it. Easy installation in .75" hole in any flat panel. The spring-loaded cover keeps out the crud. 3"×1.5"×1.75". 18" lead wire, 11.5" ground wire.

12V, 40A Bosch-type relay for use with high amp draw electronic accessories like big driving lights, extra loud horns, double sided arm jesters, etc. Waterproof sealed plastic housing with metal mounting tab. Includes installation and wiring instructions. 2.125"×1"×1.25".

Completely sealed 20 amp switch with weather resistant coating and O-ring stem seal. Includes a stamped metal on-off indicator plate that fits over the 15/32" diameter, 3/8" long mounting stem and chrome plated handle. 8" wire leads. 12V. 1.25"×.75"×1.75".

Supply safe, fused power to accessory electronic devices. Uses four ¼" male blade connections for easy installation insert the best mini fuse (not included) to match the power requirements of each device. A clear cover with insulated O-ring provides protection and a water resistant seal. 15 amps per circuit. Fits almost anywhere. Simple is good. 3.2"×1.77"×1.5".

Eliminate auxiliary toggle switches and their attendant holes by installing this device, which ties into your light wiring. Connect to high-beam wire or turn signal cancel button to allow independent control of driving lights, fog lights or any accessory electrical device from a pre-existing control button.

Tap high beams or blinker cancel button to activate, LED shines green to indicate power to your auxiliary relay. This programmable pulse sensor technology is a reliable and efficient way to control auxiliary power. Includes tie wraps, wire clips, adhesive tape and instructions. Max current draw 200mA @ 12V. 1.4"×1.4"×.3".